General Information 55 NiCr MoV7 is an alloyed Quench and Tempering steel used in many tool like applications where there is need for high hardness and mechanical strength
AISI 1055 Carbon Steel (UNS G10550)Aug 23, 2012 · Physical Properties Mechanical Properties Thermal Properties Other Designations Introduction. Carbon steels are the steels having carbon as the major alloying element. They also contain up to 1.2% manganese and 0.4% silicon. In addition, the residual elements like copper, molybdenum, aluminium, chromium and nickel are present in these steels.
Chemical Composition, Mechanical and Physical Properties. ASTM A536 80-55-06 is a special ductile cast iron grade. It has comparatively high tensile strength, and also high elongation, so its is a good cast iron material. Our Dandong foundry could produce this material, and herein, we share its chemical composition, mechanical and physical
ASTM A572 Grade 50, 55, 60, 65 Steel Plates Specification A:Specimen shall comply with Specification of A6/A6M. B:Elongation not required to be determi ed for floor plate. C:For wide flange shapesover 426 lb/ft [634 kg/m], elongation in 2 in. [50 mm] of 19% minimum applies. D:For plates wider than 24 in. [600 mm], the elongation requirement is reduced two percedntage points for Grade 42, 50, and 55 [290,345,and 380], and three percentage points
ASTM A572 Grade 55 HSLA Steel ::MakeItFromThermal Properties. Latent Heat of Fusion. 250 J/g. Maximum Temperature:Mechanical. 400 °C 750 °F. Melting Completion (Liquidus) 1460 °C 2660 °F. Melting Onset (Solidus) 1420 °C 2590 °F.
4 rows · Dura-Bar 80-55-06 can be oil quench hardened from 1600° (885° C) to a minimum hardness of Rockwell
Harvard SteelThe following Table is a direct conversion chart to convert coating weight from g/m 2 to oz/ft 2 on a per-side basis. Note that, although a precise conversion between the metric categories (20G/20G, 40G/40G, etc.) and ASTM A653 G and A categories (G30, G60, etc.) cannot be made, a 90G/90G coating category (metric) is approximately equivalent to a G60 coating category (ASTM A 653
J55 Continental AlloysJ55. General purpose manufactured to API specification 5CT. Similar to K55, except that the minimum tensile strength is lower. Available in casing dimnesions of 114.3 mm (4.5") to 508 mm (20") Available in tubing dimensions of 26.7 mm (1.05") to 114.3 mm (4.5") Product Group:OCTG and Linepipe.
Mechanical Properties of Solids; Mechanical Properties of Fluids; Thermal Properties of Matter; Thermodynamics; Kinetic Theory of Gases; Oscillations; Waves; Electric Charges and Fields; Electrostatic Potential and Capacitance; Current Electricity; Moving Charges and Magnetism; Magnetism and Matter; Electromagnetic Induction; Alternating Current; Electromagnetic Waves
Physical Properties of Ductile Iron and Alternative MaterialsIn all grades in this specification chemical composition is subordinate to mechanical properties. However, the content of any element may be specified by mutual agreement. For maximum shock resistant parts to be used at sub-zero temperatures.
STAINLESS STEELDec 13, 2016 · TABLE 1 TYPICAL ROOM TEMPERATURE MECHANICAL PROPERTIES UTS ksi. (MPa) 0.2% YS ksi. (MPa) Elongation % in 2" (50.8 mm) Rockwell Hardness Type 304 95 (655) 42 (290) 55 B84 Type 304L 95 (655) 40 (276) 55 B82 TABLE 2 ELEVATED TEMPERATURE MECHANICAL PROPERTIES Temperature °F (°C) UTS ksi. (MPa) 0.2% YS ksi. (MPa) Elongation % in 2" (50.8 mm)
Grade 55 weldable steel, permanent manufacturers and grade identication, and impact properties for Grades 55 and 105. 1.4 Zinc coating requirements are in Section 7. 1.5 Suitable nuts and washers are listed in 6.7. Washers are detailed in 6.8. 1.6 This specication does not cover mechanical expansion
XC55 / XC 55 - Steel grades, Properties and Global StandardsMechanical properties / Mechanische Eigenschaften / Caracteristiques mecaniques of grade XC55. Mechanical Properties. Physical Properties. Heat Treatment. More. Technological Curves. C55 / C 55 - Steel grades, Properties and Global StandardsThis page cover the C 55/C55 Chemical element, Mechanical Properties, C55 Datasheet, Cross Reference of C55 Mainly used for .